BCT Logo
Bergen Cable Technology

Home

Products

Technology

Quality

About Us

Contact Us


Join us on FacebookFollow us on TwitterView our You Tube Videos


Corporate
Capabilites
Brochure




 
PUSH-PULL CONTROL CABLES
Intro | Conduit Selection and Fittings | Conduit Cores | Core Fittings | How to Specify

Conduit Selection

The majority of applications utilize one of the following conduits:

Braided – Typically used in light duty, pull-pull applications where there is a need for minimal bends in routing. It is not recommended for severe bends.

Bowden – Used in light duty pull-pull applications when several bends in routing are required.

Long-lay – Used in heavy duty push-pull applications where routing, combined with high loads, burst strength and good crush resistance is required.

Shown below are standard Bertrol® components, the most commonly used, developed and stocked by Bergen Cable. If your application requires a conduit, fitting, core or design other than those listed, contact us for assistance.

CONDUIT

Braided Conduit
Part no. 5087F192
Bowden Conduit
Part no. 2985F200
Long Lay Conduit
Part no. 2361F187

Detailed Image

Detailed Image

Detailed Image

CONDUIT FITTINGS

Bergen conduit fittings are cost effective solutions for large volume production requirements. These fittings are compatible with Bergen's standard conduit and may be subject to minimum order requirements. Contact Bergen Cable for additional design and selection assistance. Tolerances are for informational purposes only. Specific critical dimensions should be discussed in advance.

 
cat160
Detailed Image
Slotted Bracket

Part #: 722-00-160RH (Symmetrically Opposite)
  722-00-161LH (Shown)
Material: 1008 – 1010
Finish: None


 
cat167
Detailed Image
Angled Bracket

Part #: 722-00-167RH (Symmetrically Opposite)
  722-00-168LH (Shown)
Material: 1008 – 1010
Finish: None


 
cat164
Detailed Image
Fixed Bracket

Part #: 722-00-164RH (Symmetrically Opposite)
  722-00-165LH (Shown)
Material: 1008 – 1010
Finish: None


Threaded End

Part #:472-00-091
Material: 1215 / 12L14
Finish: Zinc Plate w/Clear Dichromate
cat091
Detailed Image


Die Cast Threaded End

Part #: 578-00-008
Material: Zamak #3 Zinc
Finish: As cast
cat008
Detailed Image


Plain End Cap

Part #: 494-00-019
Material: Brass 260 70/30
Finish: Bright
cat4019
Detailed Image


MOLDED CONDUIT FITTINGS

The majority of designs utilize one of the standard fittings listed below. These molded end fittings are compatible with Bergen's standard conduit and cores and may be subject to minimum order requirements. Contact Bergen Cable for additional design and selection assistance. Tolerances are for informational purposes only. Specific critical dimensions should be discussed in advance.

Snap-In (Wide Groove): 587-00-012 Snap-In (Narrow Groove): 587-00-021
Material: Nylon Material: Nylon
cat012
Detailed Image
cat021
Detailed Image


One-Way Snap-Thru: 587-00-010 Removable Snap-Thru: 587-00-014
Material: Nylon Material: Nylon
cat010
Detailed Image
cat014
Detailed Image


Snap Tab: 587-15-020 Threaded End: 587-00-019
Material: Nylon Material: Nylon
cat020
Detailed Image
cat019
Detailed Image


Shock Release: 990-00-797/843 90° Conduit Elbow: 537-00-022
Material: Nylon Material: Delrin
cat797
Detailed Image
cat022
Detailed Image


Custom Control Cable

Miniature Control Cable

 

 

Bergen Cable Technology, LLC
343 Kaplan Drive, Fairfield, NJ 07004 USA
Telephone: 973-276-9596 * Fax 973-276-9566 * Email: sales@bergencable.com
© 2015 Bergen Cable Technology, LLC. All rights reserved.